How To Build A Shed (and Get It Right The First Time)-00-5108

By Author: Paul Calcic
Total Articles: 4393
Comment this article

Naturally, having a storage shed can come in very handy when you need to stow away your garden equipment or need to protect your garden furniture during winter. If you are constructing a shed for the first time, you want to begin by learning the construction of a shed. You can see that sheds are really quite straightforward construction which are simple to build. Following are seven simple stages you should find to be useful.

Phase 1:- Construct the Foundation
Before starting building of the base (foundation), you will first need to elect a location. Select a location where there will be good drainage. If moisture soaks close to your shed foundation, you can bank the land to re-direct the water away from the foundation. The two most commonly used foundations are the concrete foundation and the skid foundation. A concrete foundation will be permanent & everlasting, unlike the skid, select your location sensibly. Begin by clearing out and levelling off the spot. With a concrete base you will need to make forms. Arrange a layer of wire-mesh to give support and thwart cracking and pour the concrete. If you are not ...
... comfortable bulding a your concrete slab, perhaps consider using a skid foundation instead. Making a shed on a pressure treated skid foundation is considered easier to most diy'ers. The skid foundation will consist of the skids, typically 4x4 pressure treated floor bands, pressure treated floor joist, pressure treated lumber and the plywood decking. Next you will assemble these parts, before you lay down the plywood decking you will need to square it off. Measure diagonally, move the frame until each side measure the same, and lay down the flooring. In order to protect the base from decay and rot, make a gravel base. Prepare a gravel base by clear way roughly four inches of dirt, about twelve inches wider than the shed measurements and shovel in the gravel until full.

Phase 2:- The Frames for the Walls
The walls will utilise framing lumber. The wall frame will be made up of the wall band on bottom and top and the wall studs in between each of the wall bands. Moving on you stand up the walls and nail them to the foundation. If the shed walls are not too big, you can install the siding while it is still on the ground and raise it after.

Phase 3:- Building roof frame
Unfortunately building the roof frame is undeniably the hardest phase in the construction of the shed. Take your time when cutting the angles on the rafters. Once you have your first set of truss built, use it as a template to make the rest. If the roof truss are not all exactly the same, the roof will not be even. use a miter saw to cut all the framing materials, it makes cutting angles much faster and easier.

Phase 4:- Roof Decking and Siding
There is an abundance of choice when it comes to the siding. The most popular is the T-11 exterior siding or Hardiboard. They are both economical and fairly simple to put up. Install the siding of your choice to the walls. After you nail the plywood decking to the roof frame.

Phase 5:- Install Doors and Windows
When it comes to doors you will find a plethora of choices for a shed door. You might even wan to build your own or buy a door which is ready-made or maybe even install an overhead garage door. Depending on your needs and how you plan to use the new room you can determine what what works for you. Double doors are quite common for storage sheds. Making your own double doors will make your shed functional and even you a little money. For the best results search for free plans or buy plans when building a shed, plans will have all the details for your door and complete instructions. Naturally installing windows on a shed is optional. If you will be installing windows, be mindful about how the sunlight will affect the shed. Windows can let in light making it easier to see, but it may also bring in far too much heat.

Phase 6:- Roof Shingles
Naturally I don't need to warn you that working on the roof can be dangerous, think safety and take precautions at all times. Cover the roof plywood decking with roofing felt before putting on the shingles. The roofing felt will guard the plywood decking from leaks that may occur. There are many styles, sizes and types of shingles too choose from. When installing be sure to follow the manufacturer's own instructions for proper installation.

Phase 7:- Final Touches
To give your project the finish touch, adding details like trim and paint will make your shed look gorgeous and give it your own personal appeal. Paint will not only add appeal a good look, it will also preserve and make the shed last for years. Be aware of any legislation or permits before you begin this type project to ensure you don't go against any laws. Also having detailed building plans will make building your own shed easier and you will also end up with a far better shed.

About the Author:

http://easywoodworkingplans.com
I highly recommend visiting here for more info about http://mowspace.co.za