Deer Stand Plans

By Author: Jamie
Total Articles: 3534
Comment this article

Deer hunting is the most common practice in the recent times and as it is sure deer is the most active animal amongst others one should take maximum concern while hunting this animal. Those adventurous deer hunters, here is a great advice for you as to how you can erect a perfect Deer Stand so as to attain the fantastic aim and a wonderful shot. There are many things to be thought while planning a Deer Stand and to get the target for which it is advisable to follow these useful suggestions while preparing a Deer Stand. You would need a list of things in order to make a perfect Deer Stand and the other vital thing is-the elevation, that assists you to get a perfect view. The height and its uses will be explained later.

List of things to be prepared for the Deer Stand:
- Lumber and plywood (pressure treated)
- Ring shank 16 penny nails /3” sheetrock screws (for the main body of the stand)
- 40 penny spikes (connected to the tree)

- For the seat, take 2x2 feet plywood of thickness ¾” pt. coat the wood with any water-proof paint until it stops sucking any ...
... more.
- A V form slash (cut) of 6”on one side-to be put against the tree.
- Rise this seat on 2x4's(2 parallel and 4 ft long) and from the 2x4's leaving 4” uncovered from front side (the notch on the behind)
- And the thin or the narrow side of 2x4's against plywood.
- Now inside the 2x4's holding seat place 2 16 ft long 2x4's with narrow side in up direction.
- For spacing the stairs of the ladder (around 18”) now take 2 16ft 2x4's and wind up.
- From the top most measure a distance of 18 inches that is truly ideal, go on fixing steps at 18 inches each, till you come to the bottom fitting each stair with 2 screws or nails on either sides of the stair.
- The top piece and the ladder are done, place the top piece on the side of the ladder, position the ladder into the 2 2x4 and remember that the cut has on be in the backside.
- Then tilt the ladder a bit about 10-15 degree instead of placing it erect, as it will be simpler for you to mount.
- Fix the ladder to the seat with the help of the screws and now the stand is done for you.
- To position this on the tree take the assistance of an extension ladder, with your friend's support position the ladder properly, with the stand next to the tree and the adjusting the seat to the required level.
- Now take a 2x4 piece and mount up the ladder and with the help of nails fit it to the seat railings so that the board fits with the tree.
- Take a 40 penny spike and coerce it across the small board and fix it with the tree.
- For the braces, take a 2 4 ft long 2x4's and fix it just ahead of the back of the plywood sheet, and down to the ladder on either sides for support, repeat this on each step fitting in the seat 2x4's and outer surface of the ladder 2x4's using many screws and nails.
- You can also construct shooting safety fence by fitting 2 4ft long 2x4's to the braces at the point where the ladder and the seat are joint.
Elevation:
- For the elevation, you need to position the safety railings by forwarding a bit above the seating level about 21 inches or else what you can do is for extra security on the braces, take other 4ft long 2x4 on the top and another 2 4ft 2x4's fit them again from front railing to the tree, fix with nails and screws to the front railing and 40 penny spikes along the tree.
- For the back rest, take 12 by18 inch plywood and place it at a comfortable angle, fix it between the seat and the tree and your tree stand is ready.
- Finally hang a piece of cloth from the shooting railing and for the relaxation use the boat pillow, for the gun pull up your ropes and now you are all ready to go
Elevation helps to give you a good sight while shooting and thus aiding you to never miss an ideal shot, it even secures you against all the potential difficulties. You can also make it more comfortable by carpeting the interiors. To make a simple entry construct a complete-sized doorway.

Planning for a Deer Stand search no further, just log on at deer stand plans and to erect your own deer stand get help at how to build a deer stand learn to build your own comfortable Deer Stand at deerstandplans.net