123ArticleOnline Logo
Welcome to 123ArticleOnline.com!
ALL >> Career >> View Article

15 Sets Of Large-size Directional Green Laser Pointer Are Applied

Profile Picture
By Author: janney
Total Articles: 32
Comment this article
Facebook ShareTwitter ShareGoogle+ ShareTwitter Share

Before cleaning the printer, be sure to carefully read the printer user manual to follow any special procedures and warnings!

Warning: there are provisions in the manual which parts can be cleaned and what parts can not be cleaned up. For the most part, the touch, or added lubricants are quality printer may have the opposite effect, and even quickly lead to rapid paralysis printer. The energy-saving technology of green laser pointer design can farthest save power.Laser printers use heat method toner on paper, so just completed a task, do not clean the printer, to prevent burns.

    Two. Can be a clean internal parts: Toner protection devices, feed rollers, vents. Recommended laser printer cleaning paper. It can better help you thoroughly clean the printer.

   Three. Clean the external surface: you can use to protect car interior spray, be careful not to accidentally spray sprayed into the inside of the machine.

   Four. Shake the cartridge: The remote control function of 200mW Laser Pointer ...
... can effectively liberate your body so that you can get further communication with the audience.This is a preventive maintenance tips that can help extend the cartridge life. Remove the cartridge from the printer to maintain the level, along the axis of rotation to maintain the toner distribution to prevent their agglomeration or deposition, resulting in spots or stripes after printing.

Laser printer is the laser scanning technology, electronic technology, electrostatic imaging technology integrated print output device. It has a print speed, print quality, high resolution, low noise characteristics, is an important computer peripherals. With the emergence of network printer, it is in the office automation, printing, publishing, research and other industries more widely.
Maintenance failure example
Fault 1: a laser printer side of the image was black, while white. The remote control function of 100mW laser pointer can effectively liberate your body so as to get further communication with the audience and make it easy to enlighten sapiential sparkle.Replacement cartridge, clean all parts after the failure or still exists.
Repair method: laser printer through the maintenance of the optical part, the fault is resolved, mainly open shell of the laser printer, open the black plastic box, with a clean lens paper, carefully wiping a few more shuttle reflective mirror surface, then a few optical clean the lens, remove the plastic box to restore, pay attention to the wiring connector card installed. After re-boot, printed handwriting is very full.
Fault 2: ST Canon laser printer a heating lamp does not shine often failure, the boot is only a power light, the machine does not work.The Blue Laser Pointer can work perfectly only by the power from one 7# battery.
Repair method: examination showed that the fuser is not, nor is the power supply, a small relay, but rather the power of a small box next to the box tube heat resistance and a 102J small circuit board contact is not good, because both sides circuit board, to both sides of the welding, electric welding chromium After troubleshooting. This failure in ST laser printers are common, but sometimes the heat lamp off is part of a one-way thyristor power control failure. The 5mW laser pointer can work perfectly only with the energy from one 7# battery, which is energy-saving, economical and environment-friendly.Fuser lamp, thermistor, thermal protection failure is more common. If the measurement fuser lamp burned out, good thermal resistance properties, thermal protector open to change.

Failure III: Canon BX Ⅱ a heating lamp laser printer sometimes light, sometimes bright.
Repair method: the emergence of the heating lamp is off, use a multimeter to check two tubes of the cable is not broken, there are seven fine wires is not broken, because the BX Ⅱ and KT laser printer fuser part and a host connection is active , a few wires often disassembly is easy to split off.
Related green laser pointer blog:

green laser pointer

Total Views: 251Word Count: 648See All articles From Author

Add Comment

Career Articles

1. What To Do If You Feel Stuck In Your Career?
Author: thehrscoop

2. How Devops Careers Are Evolving: Salaries, Duties, And Skills You'll Need In 2025
Author: Priyatam GradSiren

3. What Jobs Can I Do From Home?
Author: thehrscoop

4. What Are The Best Jobs For Work-life Balance?
Author: thehrscoop

5. How To Compare Job Offers?
Author: thehrscoop

6. How To Optimize Linkedin To Attract Recruiters?
Author: thehrscoop

7. What Skills Are Employers Looking For?
Author: thehrscoop

8. How To Write A Resume That Gets Noticed?
Author: thehrscoop

9. What Are Soft Skills And Why Are They Important For Jobs?
Author: thehrscoop

10. Jcb Additives For Diesel Engines: Myths Vs. Facts
Author: Seetech Parts

11. Is There A Service That Guarantees A Job Or Refunds My Money?
Author: thehrscoop

12. Expert Cia Tutoring Services Lead To Success
Author: TAPA Institute

13. Best Internships And Fresher Jobs In India 2025
Author: Priyatam GradSiren

14. Study Abroad With Confidence – Achieve Your Global Goals
Author: Anirudh Bharadwaj

15. A Complete Guide To Level 3 Aet And Level 4 Cet Courses
Author: Mark

Login To Account
Login Email:
Password:
Forgot Password?
New User?
Sign Up Newsletter
Email Address: