Buildtech India Corporation Offers Paver Blocks Chennai, Paver Blocks Manufacturer Chennai, Kerb St

By Author: Mr. Arjunan
Total Articles: 3
Comment this article

Why to choose BIC Blocks/Pavers:
• High Strength and longer life as compared to other paving materials
• Less maintenance and Major cost savings
• Can be laid very fast, no waiting time and no curing required, can be used immediately after laying
• Can be removed and re-laid when it is necessary without much of cost
• Easy to install and no curing required after laying
• Non slippery / Anti skidding due to chamfered edge
• Environment friendly as they allow rain water to flow back in to the ground through the sand joints and separate rain water harvesting in not necessary
• Wide range of shapes and laying patterns can complement the architectural style of your dream project
• Finest infrastructure to cater to bulk requirements in short times
CEMENT PAVER BLOCKS
The paver blocks we manufacture are of stringent quality and all of our pavers are guaranteed to be free from defects or workmanship. They all have smooth surface and rolled edges and ideal for both domestic and commercial pathways, driveways. They are sturdy and do not break. They enhance ...
... the beauty of your driveway or pathway and also easy to maintain. We also manufacture designer paver blocks which are made in addition with white cement.
Paving blocks used for external floors are in great demand in modern building owing to their beauty, durability and economy. Highly wear-resistant in nature, the life of the blocks is much more than the ordinary P.C.C done in the external areas
SHOT BLASTED PAVERS
We are one of the reputed manufacturers and suppliers of shot blasted pavers. They are manufactured using highest quality products possible through our highly skilled workers. These pavers are developed by us keeping into consideration the current market trends. Use of highest quality products provides these pavers optimal level of durability and makes them last for a long period of time. We offer these pavers in different sizes as per the requirement of the customer.
Application:
Exteriors and Open spaces like Foot-paths, Side-Ways, Garage, Parking, Open areas, Promenades, Swimming Pool Decks, Foyers, Building Compounds, Drive-Ways, Porticoes, Car ramps, Corridors & Verandas, etc.- where good finish, antiskid properties or textured look is desired.
Features :
• Natural thermal insulation
• Superior compression strength
• Light weight (up to 40% reduction in dead load).
• Environment friendly
• Additionally, Hollow Blocks are lightweight (up to 40% reduction in dead load) & provides natural thermal insulation
Benefits :
• Up to 60% reduction in cement mortar consumption
• 30% reduction in plastering cost
• Almost 500% improvement in labour productivity - thereby substantial reduction in labour cost
• Saves cement in masonry work & reduces cost of construction
• High value with high quality and low price
Laying Contracts:

As a service provider we also undertake laying contracts for paving blocks & exterior tiles.
Desired conditions for laying of pavers :
• Set the floor level with wet sand for 50mm thickness and compact by using vibrating plate compacter.
• Keep the sand with moisture content. Do not use sand, which is 100% dry.
• Don't spread the sand for longer areas, as it will dry out and reduce the performance. Use sand of 50mm spreaded property.
• Lay the interlocking paver in compacted sand floor and tap gently with a rubber mallet to get perfect joints.
• Spread river sand on the laid area to fill the joint gaps and run the vibrating plate compactor to get the perfect level.
• Construct retention wall all-around the laid areas to arrest the movement of paver blocks.
• It is recommended to provide the slope of 3 inches on the wider side and 2 inches on the linear side for every feet of the laying area. Important instructions for laying floor tiles :
• Prepare base mortar with cement and sand in the ratio of 1:4.
• The total mortar thickness should not be more than 25 mm.
• Set the levels for the floor. ie.,, dead level or slop to be specified.
• Prepare cement slurry with cement and water to form a thick paste and spread it on the leveled mortar.
• Wet the rear side of the tile with water. (Complete immersion of tile is not necessary)
• If tiles are square or rectangular in shape, set the right angles for the area and place the first tile along the right angle line on base mortar. Tap gently with the rubber mallet to get perfect level.
• After laying, immediately clean the surface of the tiles with clean, wet sponge Ensure that the base mortar cement, which squeezes through joints, does not settle on the tile.
• Also make sure that the water used is not hard or brackish.
• Do not use the area laid for 48 Hours
• Fill the joints with pointing materials ie., mixture of white cement and desired color pigment. For higher quality of finishes, you could use, if required, a polymer based cementitious tiling joint filler.
• To get desired colour/shade, mix the same with water to form a smooth paste, which should be applied to the joints, preferably with the use of a rubber squeeze. Do not apply the pointing material all over the surface.
• Allow the pointing material to set for 15 minutes and clean the surface of the tile with clean wet sponge, in order to remove the excess pigment on the tile surface.
• Wash the surface with soap water or mild detergent to get a clean surface.