How To Replace The Spider Assembly In An Lg Washer

By Author: shanker
Total Articles: 7
Comment this article

The spider assembly in an LG washer is a critical component that supports the drum and allows it to
spin smoothly. Over time, this part can corrode or break due to constant use, high moisture levels,
and exposure to detergent. A damaged spider assembly can cause loud noises, vibration, and
inefficient washing performance. Replacing the spider assembly may sound daunting, but with the
right tools and steps, it can be done at home. Here's a step-by-step guide to help you replace the
spider assembly in your LG washer.
Tools and Materials Required
1. Screwdrivers (Phillips and flathead)
2. Socket wrench set
3. Pliers
4. Hammer and rubber mallet
5. Towels or rags
6. Replacement spider assembly (ensure it’s compatible with your LG washer model)
7. WD-40 or penetrating oil (optional)

Step 1: Prepare the Washer
1. Unplug the Washer: For safety, disconnect the washer from the power supply.
2. Turn Off the Water Supply: Shut off the water valves and disconnect the hoses.
3. Drain Excess Water: Use a drain hose or tilt the washer ...
... to remove any remaining water from
the drum.

Step 2: Access the Drum
1. Remove the Top Panel: Unscrew the screws at the back of the washer and slide the top
panel off.
2. Detach the Front Panel: Remove the control panel, door lock assembly, and unscrew the
front panel. Gently disconnect any wiring harnesses.
3. Take Out the Drum Assembly: Remove the belt from the motor and pulley. Then, detach the
shock absorbers and suspension springs to lift the drum assembly out of the washer.

Step 3: Disassemble the Drum

1. Separate the Drum: Unscrew the bolts securing the outer drum halves and carefully pry
them apart.
2. Remove the Inner Drum: Gently tap the drum shaft with a rubber mallet to release the inner
drum from the spider assembly.

Step 4: Replace the Spider Assembly
1. Inspect the Spider Assembly: Check for signs of corrosion or cracks. If the assembly is
damaged, proceed with replacement.
2. Remove the Old Spider Assembly: Unscrew the bolts securing the spider assembly to the
drum. You may need to apply WD-40 if the bolts are stuck due to rust.
3. Install the New Spider Assembly: Align the new spider assembly with the drum and secure it
with the bolts. Ensure they are tightened evenly to prevent wobbling.

Step 5: Reassemble the Washer
1. Reattach the Inner Drum: Insert the drum shaft into the bearing housing and secure it in
place.
2. Reassemble the Outer Drum: Reconnect the two halves of the outer drum and tighten the
bolts.
3. Reinstall the Drum Assembly: Attach the drum to the suspension springs and shock
absorbers. Reconnect the belt to the motor and pulley.
4. Reattach Panels and Components: Secure the front panel, control panel, and top panel.
Reconnect all wiring harnesses and hoses.

Step 6: Test the Washer
1. Plug the washer back in and reconnect the water supply.
2. Run a test cycle to ensure the drum spins smoothly and no leaks occur.

Conclusion
Proper use and maintenance of your LG washer can ensure its efficiency and durability for years to
come. By following these troubleshooting tips, you can address common issues and keep your
washer running smoothly. However, if the problem persists or requires professional attention, it’s
best to contact an LG washing machine service center. LG Authorized service centers are equipped
with skilled technicians and genuine parts to resolve complex issues efficiently. Regular servicing

from an LG service center can help prevent costly repairs and extend the lifespan of your washer.
For hassle-free maintenance and expert solutions, rely on your nearest LG washing machine service
center for all your repair and service needs.