How To Install A Subwoofer In A Car

By Author: John Bowles
Total Articles: 1
Comment this article

Subwoofers are the best in creating low-frequency audio sounds. Installing subwoofer speakers in your car will upgrade the quality of the sound produced remarkably. This is because the subwoofers are specially designed to produce low-frequency sounds that make any kind of music genre sound better .

How important is the subwoofer in your car? Consider this: the single most notable difference between a premium car audio system and a car audio system is the bass. It is delivering the best sonic experience.. Subwoofer, its installation, and some benefits you may expect by adding a subwoofer are the focusing points of this article.

What is a subwoofer?

Usually, a subwoofer is a special kind of speaker designed to reproduce the low range of frequencies, better sounding, and resulting in cleaner than a standard speaker. Subwoofers work with the speakers in a car stereo system that provide a full range of sound frequencies without one, you might hear guitar solos and vocal melodies just fine, but deep bass drum beats and licks will detract ...
... and sound muffled from your listening experience.

How does a subwoofer make sound?

Like the other speakers, a subwoofer creates sound by moving air. But unlike other speakers, subwoofers are mainly engineered to generate the massive cone movement necessary for low bass frequencies. The reason for bass sounds so distorted on regular speakers because the power is essential to produce the deep bass is too taxing for a particular speaker driver, especially when you try to recompense by cranking up the bass level on the car stereo receiver. When the speakers are taxed to their limit, the mid-range and high-range sounds suffer as well.
How to make bass in your car sound best
# Flatten the signal and open the low-pass filter
Turn your sub amp's gain to the lowest side and most of the counter-clockwise position. Switch set it as high and its low-pass filter on, as it will run clockwise. It has a bass boost that helps to turn it off. If it has a remote control system, you will set it to its middle position so, later, you have the choice of cutting or boosting the bass on an individual song or others.
#Adjust the subwoofer gain and low-pass filter
Play music through the receiver about the one-quarter volume. Turn up the gain of your subwoofer amp until the sound from the subwoofer completely overpowers the other speakers without distorting.

.
#Bass boost and subsonic filter
If you have a bass boost, try to concern the turning it up to hear what the bass boost drum sounds like when you do. Applying a little bass boost will bring up to drive a lot. Be conscious with the bass boost, if you choose to use it. This is where distortion is often found in a system. If you hear any distortion, lower the subsonic amp's gain until it goes away from the boost. Use the bass boost so you can feel the beat in the air, then your subsonic filter moves.

How to install?

Required parts

-Subwoofer box and speaker; Some speaker wire.

-Amplifier

-Wiring kit

-10 Gauge or thicker and 20 foot insulated wire

-10 Gauge or thicker and 3 foot insulated wire for grounding.

-18 or 16 Gauge and 15-foot wire

-RCA cables and15 feet or longer

-In-line fuse and 50 amps or higher

- four small wood screws

-Basic tools

For the power and grounding systems wires, you will need thicker wires depending on how the amplifier is powerful. Powerful amps could really need as much as a 0 gauge wire.

Choosing an Amp and Speaker

When looking at amplifiers and speakers, do not look at high power. You want to run your subwoofers on its RMS rating rather than the high rating.

For best sound, keep the impedance the same too for getting the best sound.

Let's see the Kenwood KFC-W3011 as an example. Its ratings are:

-400w RMS

-1200w Peak and

-4 Ohm Impedance

A good amp for this speaker might be the Rockford P400-2. This amp has the following ratings when it is in "bridged mode."

-400w RMS

-4 Ohm Impedance

Choosing the size of a speaker is also important.
Run Wires and Wiring the Audio
We will start from the battery by wiring the power. It is essential to get the power from the battery and not from the fuse box. Run the maximum power cable through the hole in the firewall and make sure to leave sufficient wire to get to the battery.

While you have the carpeting loose, run the RCA and 16-18 gauge cables from the trunk as close to the back of the main unit of stereo as possible, leaving a little slack from both ends.

If your stereo does not have the cable connections, you will have to join the wires into the rear speaker wires. Better yet, to go out and buy a new stereo which has RCA. They are not too expensive anymore.

Put the speaker in the box

Put the speaker in the box for making sure the slightly thin gasket thing is on it.
Then screw the speaker into the box for using the holes on the outside rim of the speaker.
Then set the subwoofer in the trunk of your car.

Adding Power
Finally, connect the power cable to the battery of the car. You just shove your wire between the post on the battery and the battery clip.

You will make sure a large fuse is in the fuse holder of the car.

Conclusion:

In a nutshell, better quality subwoofers will definitely progress your car sound system and help it to better perform. This is guaranteed because subwoofers will support your car speakers to increase their durability and sound better as well.