123ArticleOnline Logo
Welcome to 123ArticleOnline.com


Here's the recent articles submitted by susana terlicki

Articles By susana terlicki

Page: << <    1 [2]  3    > >>


Fans And Blowers From Buffalo Blower / New York   By: susana terlicki
Buffalo Blower / New York supplies highly specialised blower packages for the nuclear industry and equipment for a number of other applications, including gas CO2 circulator blowers, or submerged blowers, that provide the heat transfer in the Advanced Gas cooled Reactors and which in turn provide substantial part of nuclear generated electricity; units that once installed operate with no maintenance during plant operation. Centrifugal and axial fans are also provided for the cooling and other auxiliary systems.(read entire article)
View : 30 Times
Category : Service

Force Draft Fan And Blower   By: susana terlicki
Factors in the design of ventilation systems include the flow rate (which is a function of the fan speed and exhaust vent size) and noise level. If the ducting for the fans traverse unheated space (e.g., an attic), the ducting should be insulated as well to prevent condensation on the ducting. Direct drive fans are available for many applications, and can reduce maintenance needs.(read entire article)
View : 79 Times
Category : Education

Heavy Industry Blowers   By: susana terlicki
Boiler fans create efficient combustion by supplying a consistent and reliable ait flow. Induce Draft Fans (I.D. Fans) operate at elevated temperatures and draw the air stream through the combustion chamber, then push it through pollution control equipment. Forced Draft (F.D. Fans) or Combustion Air Fans push the air stream into the boiler combustion chamber. Multi-Fuel Burning Power Boilers are used to create steam for different power needs. Induced Draft Fans are typically AMCA arrangement 3, single or double inlet with inlet box(es). Wheels often require abrasion resistant construction with radial tip or backwardly curved blades. Combustion Air FD Fans are typicallyconstructed of carbon steel, and utilize airfoil or backward inlined blade design. Common AMCA arrangements for combustion air fans are arrangement 3 and 8, both with inlet vane or outlet damper control.(read entire article)
View : 108 Times
Category : Others

High Pressure Vaneaxial Ventilators   By: susana terlicki
Industrial Pressure Blower Co. has devloped a new high pressure small vaneaxial fan that finally resolves the problem of boosting air flow in long ventilation ducts of today's large residential houses.(read entire article)
View : 23 Times
Category : Service

High Temperature Fan And Blower   By: susana terlicki
There are two major types of high temperature fans - centrifugal and axial: Centrifugal Wheels: * Multiblade forward curve wheel. This type of wheel is usually specified where there is a necessity for large volumes of flow against low to medium static pressure requirements. The forward curve blade is that it delivers the same volume of air as either the backward or radial blade wheel, at a lower fan speed, which is important due to wheel stresses at elevated temperatures. This fan is the most common type used in all types of heat treatment operations except where a buildup of material on the blades could occur, as wheel unbalance would result. * Radial Blade, paddle wheel type fans. This type of wheel is usually specified where there is a necessity for medium volumes of flow against medium to large static pressures. The paddle wheel is considered a self cleaning type of wheel. It could be used where there are various materials or dust in the air stream. Due to its structurally strong design, it is used in many heat treatment applications at very high temperatures where maximum fan longevity is desired. Axial Blade Wheels: * The axial blade wheel is usually specified where there is a need for very large volumes of flows against low static pressure. Axial wheel like the multi-blade forward curve type wheel could cause an axial fan to deliver different air volumes at the same static pressure, if the total pressure requirement of the fan system was underestimated. This type of fan is ideally suited where a large volume of flow is required with a minimum of duct work and is used extensively for small and large furnaces, such as aluminum annealing.(read entire article)
View : 63 Times
Category : Technology, Gadget and Science

Industrial Blowers And Fans From Fans Mall   By: susana terlicki
Fans and ventilators are classified into propeller, tube axial and vane axial styles, and each type has different characteristics. Propeller fans consist of only a motor and propeller and therefore are the simplest. Tube axial are similar to propellers but has a venturi around the propeller to reduce the vortices. Vane axial fans are equipped with vanes that trail behind the propeller in the airflow to straighten the swirling flow.(read entire article)
View : 63 Times
Category : Others

Industrial Blowers In Series   By: susana terlicki
Advantage of blowers in series is that of the availbale space. If system must be expanded and increaases the CFM requirements, the allotted space for the original blower may not be large enough for a single large blower, but might be large enough to istall two smaller blowers in series to obtain the necessary pressure.(read entire article)
View : 24 Times
Category : Others

Industrial Fans   By: susana terlicki
As specialists in air moving applications and equipment, Industrial Pressure Blower Co. understands industrial blower technology and designs systems for a host of facilities and industries, and work with the best names in industrial blower equipment, including TCF,NYB, IAP. A blower can achieve much higher pressure than a fan, and can be used to produce negative pressures for industrial vacuum systems.(read entire article)
View : 76 Times
Category : General

Industrial Frocess Fan By Buffalo Blower / New York   By: susana terlicki
The pulp and paper industry is heavily energy intensive with both power and heat being essential for production. Boilers may be fuelled by various biomass wastes, black liquor or coal, and the erosive and corrosive exhaust gases present challenges to the associated fan and heat exchanger equipment. Buffalo Blower / New York provides fans for pulp and paper mill boilers to meet these demands.(read entire article)
View : 80 Times
Category : Others

Industrial Radial Fans Ventilators   By: susana terlicki
Radial fans can also be known as a centrifugal fan, which is made up of three different types of blade settings. They are the straight steel plate paddle wheel, the forward multi-vane multi-blade and the backward turbo vane. They are also used in Industrial type situations such as factories, large underground carparks and gymnasiums. They can be used in lots of different situations where there are large enclosed open spaces which need some type of circulation, whether that be blowing cold air through the premises or to just have some sort of air movement. There are different types of fans, which can be put in an industrial factory such as a mounted fan or a freestanding fan. Obviously to do a large area you need a large fan so having it mounted can be a benefit whilst having it freestanding can also be a benefit because it can be moved if need be. There are also different noise levels of these fans but most fans these days are relatively quiet especially in an area such as a factory.(read entire article)
View : 64 Times
Category : Others

See As RSS
Login To Account
Login Email:
Password:
Forgot Password?
New User?
Sign Up Newsletter
Email Address:
Google