123ArticleOnline Logo
Welcome to 123ArticleOnline.com!

ALL >> Writing >> View Article

Analyze The Steel Type Coal Ball Grinding Mill Faults

By Author: yuan shuai
Total Articles: 4

1. The little pineapple snaggletooth
In the daily use of Ball Mill, the little pineapple snaggletooth happens most often, the reasons are as follows:
(1). The little pineapple design strength is weak, and the manufacturing quality requirements is relatively low.
(2). The lubricating of the little pineapple is bad, the mesh is bad which lead to localized wear, bubbling, and material quality coming off. The local stress concentration is worsened which speed up the snaggletooth.
(3). Supercharge caused by the too many steel balls added into the Coal Ball Mill in production primary which lead to the coal ball mill electric current reaches to 130A. Decrease the steel ball loading capacity, keeping the current at around 120A. (the current raises 1A with one ton steel ball added,)
2. The little pineapple tooth surface abrasion
The gear wheel surface generally presents bubbling, peeling, scallops, and such corrosive pitting phenomenon. Besides the little pineapple tooth surface temperature is high which makes the coal grinding ball mill gear teeth attrition condition seriously.
The reasons are as follows:
(1). The coal grinding ball mill protection cover sealing is not good. There is no sealing on the association point of activity and inertia between the Coal Mill hollow shaft and shelter which speed up the ash entering to the big pineapple. The preheater of the boiler is the three branch warehouse, with one way the secondary air of the blower, one way the primary air of the primary air fan. As the primary air pressure is over-high, it blows down the ash accumulated from the smoke side carrying by the preheater heating surface and takes it away. The pipeline weld bond of the hot air system is unqualified which leads to serious leakage. The ash then enters to the wheel gear shield and speed up its attrition.
(2) The alignment pin problem: It is regulated that the temperature difference measured along the little cutter teeth width should be no more than 8??, and the highest temperature on the tooth surface should be no more than 100??. Hit the alignment pin in after the intervals between each part is normal. When the temperature difference is more than 8??, raise the bearing end of low temperature. One of the reasons for the ball mill tooth surface attrition is that the alignment pin is not hit due to the great work amount which is also the reason why some individual little cutter teeth surface is high and the two ends temperature difference is relatively large.
It consists of motor, reducer, case, milling device, separator, outlet, coal feeding pipe, loading device, control box and sealing apparatus. The fittings are all of superior performance in the world at present. We ensure good quality and durability of the whole machine.

1) The concrete base weight required is only 3 times of that of other similar machines thus the construction expenses is greatly reduced
2) Small vibration while using and doesn't need shock-absorbing device
3) Large load adjustment scope, so it can run under various environments
4) Can bear very strong explosion pressure
5) The grinding roller adopts new material and new craft, which ensures long service life and low maintenance cost
6) There is gap between the grinding parts; it can start with load or offload. Get Beneficiation,Ceramic Ball Mill,Ball Mill From http://www.stone-crusher-equipment.com

Total Views: 105Word Count: 552See All articles From Author

Writing Articles

1. Monofilament Extrusion Plant:-
Author: Rudrik Trivedi

2. Write Good Content For Your Specific Blog
Author: Andrew Mccann

3. 7 Strategies To Create Content For Web Site Without Writing
Author: Andrew Mccann

4. Tips For Successfully Putting Yourself ‘out There’ As An Entrepreneur
Author: deepa

5. Holi Festival In India | Online Magazine | Banani Vista
Author: Khyati Gautam

6. Have The Best Online Essay Writing Service For Your Help
Author: David Shaw

7. Coursecrown Offers Short Term Professional Courses In Delhi
Author: Akanksha

8. Dissertation Writing Firm
Author: Willow Paul

9. What Importance Do The International Research Journals Hold?
Author: John Watson

10. Helpful Tips For Young Writers Who Are Looking To Get Their Book Published
Author: Marianne Rugard Jarvstrat

11. 3 Major Signs Of Hypothyroidism And The Role Of Endocannabinoid System
Author: Robert Smith

12. We Need To Address The Danger From Trump’s Fake News Awards
Author: Dr.gleb

13. Importance Of Blogs In Business Growth
Author: Vineet Kumar SDingh

14. Mandarin Chinese Language Learning Strategies
Author: Michel Kern

15. Always Stay Ahead With Online Journals
Author: John Watson

Login To Account
Login Email:
Forgot Password?
New User?
Sign Up Newsletter
Email Address: